Search results

  1. PAPERINIK58666

    CB650R New member from Italy

    ah, ah, you wrote "I was fine (female)", that's why. Sorry, we're too far away, otherwise we could have met, bye.
  2. PAPERINIK58666

    CB650R New member from Italy

    Welcome , Where do you live in Italy?
  3. PAPERINIK58666

    CB650R New member from Italy

    Welcome, Where do you live in Italy?
  4. PAPERINIK58666

    All 650's Vibration?

    They particularly bother me, I have peripheral neuropathy in the limbs ... hello.
  5. PAPERINIK58666

    All 650's Vibration?

    Sometimes the 4 cylinders, if not well designed / balanced and / or isolated with silent-blocks, can have high frequency vibrations, the most harmful ones for tingling hands. The 2 cylinders vibrate more but usually at a low frequency. It then depends on the type of engine, frame, supports, etc...
  6. PAPERINIK58666

    All 650's Vibration?

    "certain vibrations! are good for the couple ...!:kiss::hungry:
  7. PAPERINIK58666

    All 650's Vibration?

    Sometimes the 4 cylinders, if not well designed / balanced and / or isolated with silent-blocks, can have high frequency vibrations, the most harmful ones for tingling hands. The 2 cylinders vibrate more but usually at a low frequency. It then depends on the type of engine, frame, supports, etc...
  8. PAPERINIK58666

    All 650's Vibration?

    Hi, about handlebar vibrations ... I tried to remove the internal pins from the grips and fill the semi-handlebars with sand, but in vain ... I am getting the best result by restoring the internal pins, with its counterweights , neoprene grips on the original grips and neoprene insulating tubes...
  9. PAPERINIK58666

    CBR650R Woodcraft Clip-On Install & Review

    Thanks, Thanks, but you risk blocking them like this ... I read about copper grease that blocks but does not form oxidation or rust. To what torque values did you tighten the various bolts?
  10. PAPERINIK58666

    CBR650R Woodcraft Clip-On Install & Review

    what tightening torques did you use for the bolts?
  11. PAPERINIK58666

    CBR650R Woodcraft Clip-On Install & Review

    Hello Dankotaru, Hello, is it correct to lubricate the various clamping screws on the new aluminum half-handlebars, or rather not? Thanks, bye.
  12. PAPERINIK58666

    All 650Rs CBR650R engine idle speed from cold

    For me too the laps are too many ... and also the warm-up time, but I don't think you can adjust it yourself without Honda assistance.
  13. PAPERINIK58666

    Aftermarket Clutch lever too far away

    I got them on Amazon too, but they solved the problem for me, and I don't keep them at the slightest distance. Maybe yours are factory wrong ...
  14. PAPERINIK58666

    CBR650R CBR 650 R 2019. More protective windshield

    Hello, but the higher Honda 2021 accessory windshield, is compatible for the 2019 model ...?
  15. PAPERINIK58666

    All 650's Vibration?

    Thanks for your experience. I too have a neuropathy problem in the peripheral limbs, (non-curable syndrome) which causes numbness in my hands even when tightening shopping bags, or cutting with scissors! But the fact remains that the CBR vibrates a lot.
  16. PAPERINIK58666

    All 650's Vibration?

    As you can see, I have had a lot of motion, but more or less they all vibrated. Perhaps the Yamaha Tracer 900 a little less than the others. The last one I had is the 4-cylinder Kawasaki Z 1000 SX, great for traveling fast, but that vibrated too ... The vibrations that bother the most are the...
  17. PAPERINIK58666

    All 650's Vibration?

    I have not said that I have eliminated them entirely, but that I have limited them. 1 I have mounted gear / rear brake pegs with rubber. 2 neoprene knobs. 3 neoprene shirts around the fork legs. 4 Neoprene on the center plate of the fork. the vibrations are not totally eliminable ... it is...
  18. PAPERINIK58666

    All 650's Magnetic Sump Plug Debris

    Of course, I've been using these filters for years on every bike. HIFLO, around 10.00 euros.
  19. PAPERINIK58666

    All 650's Magnetic Sump Plug Debris

    They are metal filings, the clutch has consumables but not ferrous. Never found metal residues in the oil filter, they probably stop first in the magnetic plug. However, personally I replace the filter together with the oil, for what it costs ...
Top Bottom